Very fast shipping.
Shipped very fast. Read More
Ships FREE in the USA!
The Halcyon backplate pocket is the most efficient means to store any of the various Halcyon inflatable markers with ease. Stowing your favorite lift device in a Halcyon Storage Pak provides a hassle-free storage place without compromising the ability for rapid deployment. The Pak bolts directly onto your backplate and the downward-facing pocket can even be used to stow the 6-ft. long Diver’s Life Raft.
Ditch the antiquated weight belt and carry your weight easily and safely with these pockets from HOG Gear. Featuring a tough nylon construction and quick dump capabilities, these weight pouches will be a welcome addition to your dive harness. Available in two sizes, 5lb and 10lb per pocket and sold in pairs. Grab a pair today and keep the weight belt in your dive bag! Harness Small Quick Drop Weight Pocket Pair-Up to 5lbs Per Pocket Harness Large Quick Drop Weight Pocket Pair-Up to 10lbs Per Pocket
Heavy Duty 2" Stainless Steel Tri Glides keeps the weights on your weight belt secure and in place.
The Halcyon Trim Weight Pocket allows Halcyon divers to move up to 10 lb. (5 lb. per pocket maximum) from their waist belt or Halcyon ACB system to the cylinder. Each pocket is constructed from 1000-denier ballistic nylon with Velcro closure reinforced by a quick-release buckle. Moving weight from a diver’s waist can improve horizontal trim, leading to more efficient propulsion, lower gas consumption, increased bottom time, and greater enjoyment of the dive. Trim weight pockets also counteract the positive weight of near-empty cylinders. By counteracting this positive ballast, the trim weight pocket also encourages a head-up position at the surface.
Ships FREE in the USA!
This innovative pocket is designed to replace the Right Hand Zipper™ pocket or ACB with a bellows-type pocket, providing both convenient storage and flexible weighting. The Halcyon Weighted Bellows™ pocket has the convenient design features you have come to expect from Halcyon pockets. It is the same physical size as the familiar Halcyon Standard Bellows™ pocket but with a harness slot for fixing the pocket to the diver’s waist strap. Two triglides allow the diver to secure the pocket to either Cinch™ ACB holders or the waist strap of a Halcyon Secure Harness™ (non-cinch). The pocket can be secured to either side of the diver’s waist. Key Features of the Harness Pocket Tough Cordura® material Zippered flap storage area with internal bungies for small accessories Large pocket internal bungies for pocket contents like the Halcyon Defender™ Pro or Halcyon SMB Internal weight pocket holds 5 pounds (2.3 KG) Stainless Steel drain grommets
This product has Video Review.
• Unique cam band has hoop/buckle feature to allow complete separation of buckle from strap • 316 stainless steel buckle has a higher “lift” on the rolling edge to increase force • Higher lift causes buckle to “snap” into place eliminating unintentional release of the buckle • Easy to adjust to different cylinder diameters Includes protective pad to help eliminate scratching your tank when you slide the buckle
Bellowed velcro pocket for easy access and compact fit. 2in (5.1cm) webbing slot for easy attachment to all Hollis harness systems. Includes Stainless grommet for quick water drain.
If you don’t have the time or patience for tying knots then, the Hose Clip Retainer is the solution. This re-usable bungee with tab can be used to secure a bolt snap to a hose, a gauge or a light. Simply thread the bungee loop through the eyelet of a snap, stretch around the hose, and bring the bungee loop over the tab. Keep a dozen of these in your dive kit; you’ll be surprised how quickly your dive buddies “borrow” them never to return.
• Designed to add up to 5 pounds of bagged shot or hard weight • Attaches by sliding over the end of 2” webbing • Easy addition to XS Scuba weight belt or other harness systems • Perfect for adjusting your trim
Ships FREE in the USA!
Traditionally, SCUBA divers have relied on whistles as their only audible surface signaling device. But, if a diver is disabled and can't blow into the whistle, the whistle makes no sound at all. Equally frustrating and dangerous, if a diver needs to attract the attention of someone who is too far away to hear the whistle, the whistle is of no help. Or, what would you do if you wanted the attention of your dive buddy underwater, for whatever reason, and he was simply distracted and not paying attention to you at that very moment? Traditionally, you would be forced to swim up to him or her until you got their attention. Instead, using the DiveAlert PLUS a diver on the surface can sound a horn blast that can be heard up to a mile away! Or, DiveAlert PLUS can signal a dive buddy underwater! DiveAlert PLUS is a small and lightweight pneumatic signaling device that harnesses the power of compressed air in your scuba tank to produce a distinctive sound both above and below the surface. Using quick-connect/disconnect couplings, DiveAlert PLUS becomes an integrated part of the power inflator on your BCD. DiveAlert PLUS does not require any modification of your other equipment, and it does not interfere in any way with the normal operation of your other equipment. When you need to get someone's attention while on the surface, you simply squeeze DiveAlert PLUS and it diverts a small amount of air from your scuba tank to make a powerful and piercing sound. Or, when you are underwater and want to attract attention, squeeze DiveAlert PLUS and it diverts a small amount of air from your scuba tank to make a buzzing noise to alert your dive buddy. INSTALLATION - DiveAlert PLUS connects between the power inflator and the low-pressure hose by means of its quick-connect/disconnect hose fittings. OPERATION - Once the tank is turned on and the DiveAlert PLUS connected, squeeze DiveAlert PLUS a little underwater for a subsurface signal or squeeze it a little harder on the surface for a loud surface signal blast. Just make sure that before every dive you check that DiveAlert PLUS is installed correctly and functioning properly. Also be careful not to point DiveAlert PLUS toward yourself or toward anyone who is in close proximity to you when you activate the surface signal or loss of hearing could result. MAINTENANCE - After each use, DiveAlert PLUS should be rinsed with fresh water. This is especially important after use in chlorinated swimming pools and in other water having corrosive substances. Additionally, it is highly recommended that you blow the water out of DiveAlert PLUS before storing. This can be done by pressurizing and activating both the surface and subsurface signaling elements. We recommend that you cup your hand over the surface signaling element to muffle the loud noise. Specifications Body and Internal Elements - Injection-molded Thermoplastic Diaphragms - Stainless Steel Couplings - Chrome-plated Brass One-Year Limited Warranty Ideations design, Inc., warrants DiveAlert PLUS to be free from defects in materials and workmanship for one year from the date of purchase from an authorized DiveAlert PLUS dealer. If any functional defects appear in a DiveAlert PLUS unit within the one-year warranty period, the unit will be either repaired or replaced at the option of Ideations design, Inc. DV1 DiveAlert PLUS compatible with 85% of all power inflators DV2 DiveAlert PLUS compatible with the SeaQuest AirSource (including AirSource3 QD),Mares Air Control, Oceanic Air XS and Aeris AirLink alternate inflation regulator systems DV3 DiveAlert PLUS compatible with Tusa Duo-Air, ScubaPro A.I.R. 2, Atomic Aquatics SS1, Zeagle OctoZ and Sherwood's Gemini alternate inflation regulator systems.
The GripLock™ tank band assembly is the easy and safe solution for securing a cylinder to a BC. • Modern design • Easy to rig and adjust • Durable metal buckle • Innovative “Finger-Saver” feature (pat. pending) eliminates pinched fingers • Macro-adjustment is set just once for each cylinder diameter • Three presets cover the various diameter cylinders in the field today • Micro-adjustment for fine tuning the fit after the band is on the cylinder • Rubber traction pad on the backside of the GripLock™ provides added security • Bands may be retrofitted to all BCs • 2 sizes available – select according to cylinder and BC typ GripLock Tank Band, Long, non-Wrapture™ harness version, for: PRO QD M, Black Diamond, and WTX Harness GripLock Tank Band, Standard Length, Wrapture™ harness version, for: WTX Back Plate w/ Deluxe One-Piece Webbed Harness NOTE: Griplock Tank Bands are sold as single items.
Ships FREE in the USA!
20 lb (10lb each) integrated weight system for Solo, Switchback & Elite harness system No sag adjustable strap Lower and side D-rings for accessory attachments Bookend screw attachment for more secure fit to harness and plate
• Same design as Single Weight Pocket above, except: - Allows excess webbing from cam strap to attach to Velcro loop on front of weight pocket - Keeps cam strap webbing secure against cylinder • Designed to add up to 5 pounds of bagged shot or hard weight • Easy addition to XS Scuba weight belt or other harness systems • Perfect for adjusting your trim • Color: black
DiveAlert is a specially designed, small, light weight air horn that uses quick-connect/disconnect hose couplings to become an integrated part of your power inflator, breathable/inflator and buoyancy compensator. Installation is easy and only takes a moment. Why have DiveAlert? What would you do in a diving emergency if you needed to get the attention of the pick-up boat or someone else on the water's surface? Before DiveAlert SCUBA divers had relied on whistles or a SMB (surface marker buoy) as their only signaling devices in such an emergency. But if the diver is disabled and can't blow into a whistle (or deploy the SMB) the whistle makes no sound at all. Or if the boat operator is not looking in the direction of a diver with a SMB deployed (if the diver was able to even deploy the SMB) the diver goes un-noticed. Equally frustrating (and dangerous), if a diver needs to attract the attention of someone who is too far away to hear the whistle, the whistle is of no help. In contrast, Dive Alert enables divers, at the mere touch of a button, to generate a blast of sound that can be heard up to a mile away! There are three different models available; one for approximately 85% of standard power inflator mechanisms model DA1. There are several breathable/inflator mechanisms that require a larger coupling for a higher flow of air so there are two models to accommodate them. The model DA2X and the modelDA3X. Installation is easy and takes only a moment. Dive Alert does not require any modification of your other equipment, and it does not interfere in any way with its normal operation. When you need to get someone's attention on the water's surface, you simply press a button and Dive Alert uses a small amount of air from your scuba tank to make a piercingly 132db loud sound; even as little as 100 psi (6.9 bars) will give you a full-throated screech. Dive Alert can be heard from 1 mile (1.6 km) away. DA1 Fits All Standard Inflators DA2X SeaQuest AirSource 1&2, Zeagle OctoPlus, Oceanic Air XS, Mares AirControl DA3X ScubaPro Air 2, Tusa Duo-Air, Atomic SS1, Sherwood Gemini, Zeagle Octo-Z Features: Models Available for Almost All Inflators and Breathable/Inflators Extremely Load (132db) Signal with a Touch of a Button Works with as little as 100psi (6.9 bars) Lightweight Design Increased Dive Safety Up to One Mile (1.61 km) Audible Range Easy to Install Injection Molded Thermoplastic, Chromed Brass and Stainless Steel Construction Owner's Manual 1 Year Limited Warranty
Large retractor with locking switch.
This ultimate Octo holder is a quick release holder that has an easy BC attachment clip. The aluminum head and stainless steel key ring help secure everything and ensure it doesn't rust. It comes with a silicon spacer for smaller hose diameters to be sure the octo hose doesn't slip thru the attachment point. Compact and convenient to slip on ANY BC. Just unscrew the bottom and put your hose into the hose port, tighten up the screws, and your new octo holder is ready to go and be secure. No need to worry about your octo falling out of its holder anymore!
This Low Pressure to Inflator adaptor will add a low pressure inflator connection to any LP hose. A must for any dive kit to ensure you have a back up inflator hose for you BC or Drysuit!!
Take care of all of your gear with this Super Hanger Bundle. This bundle includes one wetsuit / drysuit hanger, one accessory hanger, and one BC hanger. You'll be able to hang up your suit, Bc, Regulators, computers, gloves, boots, fins and anything else that you take in the water with you! Super Hanger When the average hanger just doesn’t cut it, rely on the Super Hanger. We know your gear is often heavy and wet. So, we built the Super Hanger sturdy, with high quality non-corrosive materials. It holds more weight, so your valuable stuff won’t end up on the ground. One piece I-beam construction for strength. Non-corroding plastic resin will not rust Supports up to 20 pounds Proudly made in the USA 16.6 inches x 1.20 inches x 9 inches (42.16 cm x 3.05 cm x 22.86 cm) Super Accessory Hanger This unique non-corroding hanger holds gloves, booties, hood and fins for drying and storage. This unique hanger holds dive gloves, hood, booties and fins. It allows proper drying and keeps them off the floor to prevent damage. One piece I-beam construction for strength. Non-corroding plastic resin will not rust Supports up to 20 pounds Size: 1.2 x 13 x 20 inch **Due to the awkward size of this product, you may incur additional shipping fees that will not show up in your shopping cart** Super BC Hanger This non-corroding hanger is designed specially for holding a BC and regulator during drying and storage. This unique hanger is built specifically for hanging your expensive BC and regulator. Raised hooks are added to the tips of the hanger shoulders to prevent the BC from sliding off. A T-hook extends from the bottom of the hanger for draping hoses from your regulator. With this hanger your equipment will dry quickly and safely off of the floor. One piece I-beam construction for strength. Non-corroding plastic resin will not rust Supports up to 20 pounds Size: 1.2 x 16 x 10 inch
SS Carabineer Clip
Mini Retractor with Quick Disconnect
Ships FREE in the USA!
The “NEW” SEAWOLF Weight Harness from SEASOFT SCUBA The "NEW" SEAWOLF™ Weight Harness from SEASOFT SCUBA has been improved in every way. Now recreational divers have access to a commercial grade weight harness. The “NEW” SEAWOLF is designed for divers who need a large amount of weight to attain neutral buoyancy OR who have problems wearing a conventional weight belt. The heavy-duty CORDURA™ ditchable pockets are available in 30, 40 and 60 lbs. in each ditchable pocket for even the most demanding commercial diver. The release mechanism on the ditchable pockets is safe and easy to use. Just pull the YELLOW handles straight down for gravity assisted ditching of the weight pockets. The weight pockets are virtually impossible to accidentally ditch because of the way it is designed, the release only works with a straight down motion. The padded shoulder straps are designed for comfort and there is a stainless D-ring mounted behind the+ neck for surface supplied air or rope tie in. You can also order your SEAWOLF with custom D-ring attachments or accessories. NO one makes a more adjustable and comfortable commercial weight harness, it is adjustable on every plane so the SEAWOLF fits you perfectly. The weight pockets slide along the waist belt and the height is adjustable both in front and back. A heavy-duty military grade 2" acetal (polyoxymethylene) side-release 2” buckle and heavy 2” weight belt webbing holds it all together. Comfort, durability and the perfect fit – if you need a commercial grade weight harness, one you can enjoy for years - this is it! DANGER: This Commercial Weight Harness can kill you if it is not used properly or without proper training or knowledge. Its weight capacity can create NEGATIVE buoyancy that can result in the inability to become positively buoyant, even with a fully inflated Buoyancy Compensator. The SEAWOLF Weight Harness requires direct training with a knowledgeable instructor before use. Practice ditching weights with your head above the water until the ditching motion becomes natural. Regular practice should be part of your diving routine. “NEW” SEAWOLF Weight Harness • Commercial grade weight harness. • 2 ditchable weight pockets. • Adjustable on every plane, adjustable height in back and front and the waist. This creates a custom fit for every user. • Weight pockets can be moved and adjusted along the heavy webbing but will NOT move during a dive. They are secured with heavy stainless steel slides. • All connecting pieces are either stainless steel or 2” acetal (military grade plastic known for its strength) side release buckles. • Weight pockets ditch straight down for safer evacuation of weights in an emergency. You use gravity to assist you in ditching weights. This is simply safer. • Adjustable multi-position chest strap. • Padded shoulder straps for extra comfort. • YELLOW ditching handles that are easy to grasp and operate. No weaving involved! Weights go in the top, ditch out of the bottom. • Weights can be easily added after donning the weight harness through the large opening at the top of the weight pockets. The pocket closes with the extra durable #10 size nylon zipper. • The SEAWOLF™ is by far the best weight harness available to divers today. SEASOFT SEAWOLF Weight Harness Specifications Belt Material: Nylon Weight Belt Webbing Buckle Material: Shoulder, waist, release: Acetal (military grade plastic known for its strength) (polyoxymethylene) Chest: Nylon Connectors: Stainless Steel slides Closures: Weight Pockets: #10 Heavy-duty zippers; Pocket material: 1000 CORDURA Shoulder material: Padded 1000 CORDURA Accessory Points: Nickel coated grommets Weight (with packaging): 3.75 lbs.
The Sport Pocket is 6" X 9" X 2.5". It has 1 zippered compartment. It is made out of Para-pac Nylon. 5 colors available.
5lb Non Ditchable velcro close weight pockets. Can be used on tank bands for trim weight on back, or on a harness for extra weight. Sold as a pair
Individual Mesh Weight Pockets for Zeagle Ripcord BC's. Available in 12LB and 18LB capacity.
Ships FREE in the USA!
Our customizable weight harness is for divers who want the flexibilty to wear weight independent of the BCD. Designed to be used with any weight pocket in the Dive Rite line, the Weight Harness holds up to 40 lbs of weight in multiple drop pockets (NOTE: Pockets not included). Premium marine-grade stainless steel hardware is custom made to make sizing easy, plus keeps the straps in place when removing the harness as compared to over-the-shoulder straps that simply slide onto the waist strap. This unique design holds the Weight Harness in place when donning and doffing, plus prevents weight from shifting during the dive. The Dive Rite Weight Harness is easily readjusted for exposure protection, taking the diver from heavy thermal undergarments with a drysuit to a 3mm wetsuit, if desired. Weight can be placed in a variety of locations to achieve optimal trim, plus those diving in cold water with thick thermal protection can spread heavy weight between the Weight Harness and the BCD. Fully adjustable to fit any size diver. Designed to be worn beneath any BCD. Made in the U.S.A. Specs: Custom, marine-grade stainless steel hardware Two-inch nylon webbing has 2,800 lbs tensile strength Made in the U.S.A. Add On Options: Weight Pocket Sytem QB- 16lb Tech Specs: Holds up to 8 lbs (3.6 kg) in each pocket. Right hand pocket has the Dive Rite logo patch. The left hand pocket is plain, without a logo. 1680 denier ballistic nylon fabric is tear and abrasion resistant. Two-inch (50.8 mm) nylon webbing loops on the back of the pocket slide over a 2-inch webbing waist strap and secure the pocket into place. Acetyl quick buckle is used to easily secure the pocket in the holster. Nickel plated brass grommets resist rust and corrosion. 9-in high x 3.5-in wide x 1.5-in deep (22.9 cm x 8.9 cm x 3.8 cm) 12 oz (340.2 g) Made in the U.S.A. Weight Pocket System QB - 32lb Tech Specs: Holds up to 16 lbs (7.25 kg) in each pocket. Right hand pocket has the Dive Rite logo patch. The left hand pocket is plain, without a logo. 1680 denier ballistic nylon fabric is tear and abrasion resistant. Two-inch (50 mm) nylon webbing loops on the back of the pocket slide over a 2-inch webbing waist strap and secure the pocket into place. Acetyl quick buckle is used to easily open and close the pocket. Nickel plated brass grommets resist rust and corrosion. 8.5-in high x 6-in wide x 1.5-in deep (21.6 cm x 15.3 cm x 3.8 cm) 1.13 lb (0.51kg) Made in the U.S.A.
Introducing V Weight Pouches from Halcyon. Will hold up to 10 lbs of soft weight, Secure hook-and-loop closure with clip Attaches to tank band
Say Goodbye to Salt Crystals! Screw off the Zeagle Inflator Head, screw in your garden hose, and let the water do the cleaning for you! Available for use on ALL 1" corrugated BC hoses
The Dive Rite Adjustable Bungee System (ABS) allows fast and easy customization to fit any sidemount diver. The bungee cord is weaved through a custom designed, laser cut Delrin plate providing an infinitely adjustable bungee. The bungee will support even the heaviest of steel tanks without slipping thanks to the unique weaving pattern. There are no knots to tie and no tools are required--just loosen the weave at the plate, adjust to the correct length, and re-tighten. Make quick work of fine tuning your sidemount system and easily adjust for different sized tanks or varying thicknesses of exposure protection. They are also ideal for instructors and rental programs that need to quickly size the bungees for their customers. The Adjustable Bungee System can also be quickly changed between Dive Rite’s standard ring bungee system, loop bungees with a snap, or traditional loop bungees. Simply unweave the bungee, add or remove hardware as necessary, and re-weave. The bungees can be easily attached to any of Dive Rite’s sidemount harnesses using the daisy chain webbing attachment point. Alternatively they can be attached to any small D-ring or quick link attached to the side of a standard backplate or harness. The ABS uses high quality, tight weave ¼” bungee for long life and just the right amount of stretch. If the bungee does get damaged it is easily replaceable in the field. The system includes the bungee, weaving plate, and ring bungee hardware including a 2” stainless steel ring, medium quick link, and medium bolt snap. TECHNICAL DETAILS HW1026 Medium Stainless Bolt Snap HW1021SS 2″ Stainless Ring HW1014SS Medium Stainless Quick Link 30 inches (76.2 cm) of 1/4 inch (6.35 mm) Bungee Delrin bungee plate
The Utility Pocket is designed to fit masks, handheld lights and spools, yet it's expandable design means a low profile pocket that isn't bulky. At 10 inches x 3.75-inches, it expands to 3.5 inches deep when carrying larger items. A Velcro closure keeps items secure while mesh front and sides provide drainage. Unique, overlapping 2-inch belt closure means you can easily don/doff without having to slide it off a harness belt. Simply pull open the closure and remove the pocket, even while still wearing the BCD. Made in the USA. 600 denier Cordora 10"x 3.5" x .5" (25.4cm x 8.9cm x 1.3cm) empty Expands to 3.5" (8.9cm) height 3.2oz (90.7 g) Made in the USA. Great for flashlight-style primary / backup lights, Reels, Backup Mask and more!
This product has Video Review.
Needing to add weight to your Nomad LTZ Sidemount Rig? Do so quickly and effectively with the Nomad LTZ Weight Plate. The Nomad LTZ Weight Plate has 3 pockets that can accommodate up to 4 pounds each (depending on the shape and type of weight). The weight plate attaches to the Nomad LTZ using the two metal 2" slides that come sewn onto the rig, allowing for easy installation or removal. TECHNICAL DETAILS Made from ballistic nylon material Pockets close with a hook and loop fastener material Plate length: 12 inches (30.5 cm) Webbing attachments: 6 inches (15.25 cm) each
Ships FREE in the USA!
This unique evolution of the ACB10 enhances diving comfort and refines the utility of the Halcyon releasable weight system. The new, vertical position allows notably more room on the diver’s waist while supporting greater comfort for those that wish to wear a hip mounted Halcyon light. Divers not using a hip mounted Halcyon light will appreciate the additional comfort and the ability to trap a long hose beneath the ACB. The new ACB 10 is constructed from the same heavy duty ballistic nylon as other weighting products; the left pocket still contains a 2” SS D-ring for SPG attachment. Smaller size leaves more room on the waist band Ideal for use with hip-mounted primary lighting Can be used with soft or hard weights Up to 6 lb. per pocket using hard weight Easy one-click weight pouch release Carry handle on weight pouch
Complete cleaning and maintenance system for all types of B.C.D.s. Leaves B.C.D. shell, interior lining, hoses and valves conditioned and free of damaging salt crystals, chlorine and organic residue.