815 267 8400

Valves

Scuba Tank Valves - We have the best selection of tank valves around

When it comes to selecting scuba tank valves, it’s impossible to be too picky. That’s why we carry only the best.

Set Ascending Direction

27 Item(s)

per page
  • PVD PRO Valve
    $69.95

    XS Scuba

    PVD PRO Valve

    4 Review(s)

    XS Scuba's Physical Vapor Deposition (PVD) Finish Pro Valve has the same type of long lasting finish you find on expensive faucets, high-end door lock sets and premium watches. PVD is not only a beautiful finish, but is also extremely durable. Before assembly the finished marine grade brass with triple bright chrome plating parts receive the PVD finish process. The parts are placed in a vacuum chamber, where a high power electric arc is discharged at the source material blasting away some into a highly ionized vapor which is deposited on the parts. XS Scuba's black colored PVD finish is accomplished with the use of Titanium Nitride. It provides the following advantages: Significantly harder exterior finish of 250 HV, a coating thickness of 0.2 to 0.3 micrometers, incredible resistance to salt water corrosion, increased scratch resistance and a very cool tech look".  Mil-Spec black PVD finish Standard yoke outlet with spin-out DIN insertconverts to 230 bar DIN outlet 3/4" - 14 NPSM standard inlet threads Clean for pre-blended Nitrox up to 40% oxygen 1.5 handwheel rotations from fully on to fully off  Dip tube included

  • Ships FREE in the USA!

    Thermo Modular PRO Valve - Left Hand
    $79.95

    XS Scuba

    Thermo Modular PRO Valve - Left Hand

    2 Review(s)

    Standard yoke outlet with spin-out DIN insert converts to 230 bar DIN outlet Modular access  plug included 3/4"-14 NPSM standard inlet threads Threaded clip tube included Clean for pre-blended Nitrox up to 40% oxygen

  • Ships FREE in the USA!

    Thermo Isolation Manifold
    $239.95

    XS Scuba

    Thermo Isolation Manifold

    Thermo Isolation Manifold.  Your choice of DIN or PRO outlet.    Features:  8.46 inch center to center orientation High gas flow for optimum regulator performance On/Off seat built from higher strength brass with nylon seat and Teflon plated for years of smooth operation Once-piece safety assembly protected within the body of the valve Traditional copper crush washer sealed bonnet Modular access plugs R/L included for use as single valves Screw in dip tube with hex tighten feature Tactile grip black rubber handwheel Meets the requirements of CGAV9-2009 standards

  • Ships FREE in the USA!

    Thermo Modular PRO Valve - Right Hand
    $79.95

    XS Scuba

    Thermo Modular PRO Valve - Right Hand

    3 Review(s)

    Standard yoke outlet with spin-out DIN insert converts to 230 bar DIN outlet Modular access  plug included 3/4"-14 NPSM standard inlet threads Threaded clip tube included Clean for pre-blended Nitrox up to 40% oxygen Sold as left handed or Right handed, not as pair

  • Ships FREE Worldwide!

    Thermo PVD One-Piece Manifold
    $799.00

    XS Scuba

    Thermo PVD One-Piece Manifold

    1 Review(s)

    Physical Vapor Deposition The same type of long lasting finish you will find on expensive faucets, high-end door lock sets and premium watches.  Not only a beautiful finsih, but also extremely durable.  The finished brass parts are chromed as usual, but before assembly, the parts receive a final PVD finishing process.  The parts are placed in a vacuum chamber where a high power electric arc is discharged at the source material blasting away some into a highly ionized vapor which is deposited on the parts.  Our black colored PVD finish is accomplished with the use of Titanium Nitride.  It provides the following advantages: Significantly harder exterior finish of 2500 HV Coating Thickness of 0.2 to 0.3 micrometer Incredible resistance to salt water corrosion Increased scratch resistance Very cool "tech look" ON / OFF Seat Assembly Machined high tensile brass alloy Nylon high pressure seat material Teflon plated for years of smoooth operation Brass Stem Precision machined from high tensile brass Chrome plated for years of corrosion free service Sealed Bonnet Copper crush washer seal 11/16" hex socket head One Piece Safety Protected within body to guard against damage during transport Pro Outlet Combination DIN / yoke outlet Removable Spin-out DIN insert Attachement of DIN or yoke style regulator Inlet Thread 3/4" x 14 NPSM threads Standard for nearly all DOT aluminum scuba cylinders Standard for all DOT modern steel scuba cylinders Hex Wrench Tighten Dip Tubes Threaded chromed brass dip tubes Say goodbye to pliers Say goodbye to damaging chrome plating Use a 5/32"  hex wrench to install dip tubes High Flow Unsurpassed gas flow Allows Optimum Regulator performance Direct placement porting Center to Center 8.46" / 215mm Correct spacking for:Highland SB725 BandsHighland SB800 BandsHighland SB803 Bands Gas Service Clean for pre-blended Nitrox up to 40% oxygen Viton and EPDM o-rings Christo-Lube MCG 111 lubrication Nylon high pressure seat material

  • Blue Steel Convertible Valve
    $50.00

    Faber

    Blue Steel Convertible Valve

    Blue Steel 200 Bar Din/Yoke Valve is perfect for your high pressure or aluminum cylinder.  Features: Convertivble DIN/Yoke Including yoke insert Available for 3000 PSI cylinders Valve Thread Size: 3/4"-14 NPSM O2 Clean    Made in Italy

  • Ships FREE in the USA!

    This product has Video Review.

    Thermo Pro Valve 200 bar
    $79.95

    XS Scuba

    Thermo Pro Valve 200 bar

    14 Review(s)

    Premium quality Strong, Trouble-free Cylinder valves Thick, rugged valve body withstands the rigors of cave diving, wreck diving, and transport by car and boat.  Takes abuse that thinner competitors will not.   Polished finish and triple chrome plated for maximum resistance to salt damage. Other satin-finished valves have only two layers of plating. Polished surfaces have fewer imperfections in which corrosion begins.   Plug & seat assembly is Teflon coated for smooth operation and maximum resistance to salt damage.   Dual Teflon and O-ring seals provide optimal sealing at high and low cylinder pressures.   100% of all Thermo valves are pressure tested before shipping. Other companies test only a random sample.   Ergonomic design Hand wheel angle provides a comfortable lifting point for cylinders.   New hand wheel design is softer and more rounded.   Nitrox ready Thermo valves can be ordered for air or Nitrox service.   Designs for all applications K-series for U.S.-style regulator yoke   DIN series   Pro series convertible valves for use with all regulator types. Removable insert allows one valve to receive 230 bar, 300 bar, and K-style yoke regulators.   Stand-alone, dual manifold, and H-style configurations

  • Ships FREE in the USA!

    This product has Video Review.

    Hog 300 BAR Manifold
    $199.95

    HOG Gear

    Hog 300 BAR Manifold

    4 Review(s)

    Isolation Hog 300 BAR Manifold for use in twin or Double tank/cylinder configurations. 3/4" Thread, "Nitrox Ready" for Partial Pressure Blending EANX up to 40% Oxygen content. Viton orings.

  • Hog Convertible Left/Right Hand Valves
    $59.95

    HOG Gear

    Hog Convertible Left/Right Hand Valves

    10 Review(s)

    These 200bar Hog Convertible Left/Right Hand Valves are just what you need for your sidemount tanks!  No need to continue to use a Modular valve.  This valve is a simple valve, either left hand or right.  The removable insert spins out to turn this Yoke valve into a DIN valve.

  • Ships FREE in the USA!

    200 Bar Manifold
    $250.00

    Dive Rite

    200 Bar Manifold

    3 Review(s)

    All Dive Rite manifolds use two barrel o-rings to seal either end of the cross-bar, which provides better shock absorption and redundancy compared to the old-style metal-to-metal seal manifolds. Our 200 bar manifolds have a 180mm isolation crossbar that fits both 7.25-inch and 8-inch diameter tanks and recessed burst disks are protected from accidental shearing. The Dive Rite 200 bar manifolds can be converted from yoke to DIN by removing the included insert (doughnut) with a 8 mm Allen wrench. This manifold is our most popular since yoke, 200 bar, or 300 bar regulators can be used with it. Shock absorbing ribbed rubber knobs are rugged, yet easy to manipulate. All Dive Rite manifolds come standard for 3500 psi service pressures. A ll Dive Rite manifolds and valves come with Viton o-rings and oxygen compatible lubricants and are Nitrox ready up to 40-percent. Specifications:   3500psi service pressure Nitrox ready up to 40% 180mm isolation bar 4.9 lbs (2.3kg)

  • Ships FREE in the USA!

    XS Scuba Isolation Manifold
    $254.95

    XS Scuba

    XS Scuba Isolation Manifold

    6 Review(s)

     This new manifold is the result of many thousands of dollars in engineering, research, and tooling development.  Built with the inspiration and the tradition of the widely famous THERMO Isolation Manifold, the new XS Scuba isolation manifold retains the shape, high luster exterior plating,  and interior design of the THERMO, while offering several design changes that are individually small, but collectively represent a gigantic improvement. FASTER ON AND OFF - FEWER KNOB TURNS.  The XS Scuba isolation manifold offers a redesigned bonnet that provides complete valve opening in 1 1/2 turns of the valve knob.  This is a feature allows for faster valve shut-down and is a feature of  interest to most dual cylinder and technical divers.  Comes with Red/Green Safety Handwheel HEX-KEYED DIP TUBE.  The XS Scuba isolation manifold allows for the insertion of a 5/32" hex key in the end of the dip tube.  This eliminates the need to use pliers on the plated tube surface during the installation process. The XS Scuba isolation manifold is available in both the 200 BAR International or the 300 BAR DIN openings.  Left and right hand valves, along with the isolation connector, come packaged as a single unit for easy ordering.  Each valve includes the plugs to allow use of the individual valves on single cylinders.  Both versions feature 3/4" threaded tank inlets to fit all modern scuba cylinders.  Each valve comes with a 5200 PSI safety assembly installed.  

  • Ships FREE in the USA!

    Combo Cylinder Valve / Piston First Stage
    $109.99

    H2Odyssey

    Combo Cylinder Valve / Piston First Stage

    1 Review(s)

    This Tank valve is also a Piston First Stage.  Great for Backup bottles and Argon systems, it has an easy on off knob plus an over pressurization valve (OPV).  With a basic 2 low pressure ports and 1 high pressure port, it has more than is needed to be a streamlined additon to your tank.   Use the dropdown menu to add a 1" pressure gauge so you know how much gas is in your tank.   

  • This product has Video Review.

    Convertible 200 BAR DIN Valve
    $49.99

    Genesis

    Convertible 200 BAR DIN Valve

    5 Review(s)

    200 Bar DIN Valve good up to 100% oxygen.  Made in Italy

  • Ships FREE in the USA!

    Thermo Modular DIN Valve - Left Handed
    $79.95

    XS Scuba

    Thermo Modular DIN Valve - Left Handed

    Dedicated 300 bar DIN outlet Attachment of DIN first stages only Modular access plug included 3/4"-14 NPSM standardd inlet threads Threaded dip tube included Air service only

  • Sherwood Valve
    $54.99

    Sherwood

    Sherwood Valve

    A perfect example of our unsurpassed expertise in life support is our PSI 5000K valve which is the highest-rated for performance and durability in the scuba business. We design it, make it, and stand behind every element of it. Available in 3000 or 3300 PSI

  • Thermo DIN H Adapter
    $71.95

    XS Scuba

    Thermo DIN H Adapter

    Dedicated 300 bar DIN Outlet Attachment of DIN first stages only Attaches to all Thermo Modular Valves Attaches to all XS Scuba Modular Valves Left hand H adapter attaches to left hand modular valve Air Service ONLY

  • Ships FREE in the USA!

    Valve H Adapter
    $79.00

    Dive Rite

    Valve H Adapter

    1 Review(s)

    The H adapter evolved from the Y valve. Originally produced by Sherwood in the 80's, the dual outlet Y valve for yoke regulators allowed divers to do limited overhead penetration while still having two independent regulator systems for redundancy. The H adapter is the latest generation of dual outlet single tank diving. The H adapter screws into the crossbar outlet of the K valve so a second regulator can be attached for technical diving. The H adapter is available in 200 bar only and equipped with shock absorbing ribbed rubber knobs that are rugged, yet easy to manipulate. As an integrated part of the valve no relief disks are necessary. All Dive Rite valves come with Viton o-rings and oxygen compatible lubricants and are Nitrox ready up to 40-percent. Ribbed, rubber knobs with stainless steel inserts are tough, yet easy to open/close Double barrel o-ring seals provides redundancy and better shock absorption Brass with chrome-plated finish gives rugged protection and durability    

  • Ships FREE Worldwide!

    Gas Block
    $775.00

    Aqua Lung Military

    Gas Block

    Did you know the Apeks Gas Block is perfect for public safety teams using a pony bottle?  The Universal Mounting Plate allows for removal of the gas block and used on another set of gear.   Four 3/8in MP outlet ports – Marked primary and bailout ports – One-way check valve

  • Ships FREE in the USA!

    Hog 200 Bar Manifold
    $199.95

    HOG Gear

    Hog 200 Bar Manifold

    3 Review(s)

    Hog 200 Bar Manifold for use in twin or double tank/cylinder configurations. 3/4" Thread, "Nitrox Ready" for Partial Pressure Blending EANX up to 40% Oxygen content. Viton oring PLUG insert for use with Yoke first stage regulators.

  • Thermo by XS Scuba K Valve
    $60.00

    XS Scuba

    Thermo by XS Scuba K Valve

    1 Review(s)

    Deluxe K ValveVA100-30AAluminum Cylinders Standard yoke outlet 3/4" - 14 NPSM inlet Threaded dip tube included Service pressure: 2400, 3000 psi

  • Ships FREE in the USA!

    200 BAR Valve
    $95.00

    Dive Rite

    200 BAR Valve

    2 Review(s)

    Dive Rite valves are chrome-plated brass for rugged protection and durability. Double o-ring seals provide redundancy as well as better shock absorption. Ribbed rubber handwheels are tough, yet easy to open and close. The right valve paired with the left can be used for independent doubles, a doubles manifold, sidemount, and rebreather cylinders. The valve is modular so divers can use them independently on single tanks, put them together to form an H-valve, or use an isolation bar to build a manifold for double tanks. All Dive Rite valves come standard with 3500 psi (242 bar) working pressure relief disks, built with oxygen compatible o-rings and lubricants, and are Nitrox ready up to 40-percent. All Dive Rite valves are easliy converted between DIN and yoke by using the provided DIN to yoke insert. The insert is installed and removed with an 8mm hex key.   3500 psi (242 bar) working pressure Nitrox ready up to 40% DIN or yoke compatible with included insert 1.85 lb (.84 kg)

  • Ships FREE in the USA!

    Thermo Modular DIN Valve - Right Hand
    $79.95

    XS Scuba

    Thermo Modular DIN Valve - Right Hand

    2 Review(s)

    Dedicated 300 bar DIN outlet Attachment of DIN first stages only Modular access plug included 3/4"-14 NPSM standardd inlet threads Threaded dip tube included Air service only

  • Hollis H-Adapter
    $70.00

    Hollis

    Hollis H-Adapter

    Hollis H-Adapter for modular tank valve

  • Ships FREE in the USA!

    PRO Valve - 2400 PSI
    $84.95

    XS Scuba

    PRO Valve - 2400 PSI

    1 Review(s)

    Standard yoke outlet w/spin-out adapter converts to 230 bar DIN outlet 3/4" - 14 NPSM inlet Clean for pre-blended Nitrox up to 40% FO2 Hex wrench tighten dip tube O-ring sealed bonnet Easy grip rubber handwheel Service pressures: 2400, 3000, 3300, 3442 psi Nitrox Ready

  • Harrison K Valve
    $60.00

    Genesis

    Harrison K Valve

    Sherwood Harrison 3000 PSI Tank K Valve All Harrison valves are produced to meet or exceed the highest US and international standards; including ISO 10297 and CGA V-9. Harrison Valves™ are rigorously tested through a robust quality assurance system, and Harrison Valve™ maintains carefully monitored manufacturing processes to ensure that all Harrison valves meet or exceed design and performance specifications. Teflon-coated plug threads for superior lubrication.Dry lubrication means you never have to apply grease. Specially designed burst disk assembly that evenly distributes escaping air, preventing your tank from spinning or tipping if the burst disk vents.FEATURES A smooth operating, all-Teflon seat for exceptional qualityPrecision threading for a clean and tight seal.High air-flow capacity Exceeds CGA V9 standards for cylinder valves for compressed gases. Cycle tested 5000 times to exceed all real world applications. Engineered with high flow charactaristics to maximize regulator performance Valve design allows for easy and comfortable cylinder handling Slant back handwheel allows easy access Easy operation under all pressures. Protective and attractive chrome plated finish. Positive hand wheel grip for easy indentification of on/off direction. 100% leak testing on entire production. Designed with proven and readily available replacement valve parts. 3/4" NPSM, 14TPI

  • 180 mm Isolation Crossbar
    $95.00

    Dive Rite

    180 mm Isolation Crossbar

     180 mm Isolation Crossbar

  • Right Hand
    $72.00

    XS Scuba

    Thermo Pro H Adapter

    Standard yoke outlet with spin-out DIN insert converts to 230 bar DIN outlet Attaches to all Thermo Modular Valves Attaches to all XS Scuba Modular Valves Right hand H adapter attaches to right hand modular valve Left hand H adapter attaches to left hand modular valve Clean for pre-blended Nitrox up to 40% oxygen

 
 

Set Ascending Direction

27 Item(s)

per page